基于三菱PLC自動旋轉門的控制系統硬件設計【含CAD圖紙和說明書】,含CAD圖紙和說明書,基于,三菱,plc,自動,旋轉門,控制系統,硬件,設計,cad,圖紙,以及,說明書,仿單 摘　　要 三翼自動旋轉門作為自動門中的頂級產品，旋轉門給人以親切大方的感覺，同時營造出奢華的氣氛，堪稱建筑物的點睛之筆。其最大的特點在于它“永遠開門，又永遠關門”，即對于人來說，門總可以打開，可對于建筑物來說，門又總是關著。因此，自動旋轉門在功能方面具有獨特的發展。 本次的畢業設計主要論述了三翼自動旋轉門的系統設計過程，主要對控制系統、安全系統做了詳細的分析和設計。控制系統用PLC負責完成控制任務，根據要求選定PLC型號為FXOS-32MR-001,并查閱相關資料確定PLC接線圖。由變頻器來實現門體多種轉速的調節功能，根據功能要求選取了佳靈JP6C-T9-0.75型變頻器，并畫出了其電控系統電氣原理圖。安全系統采用紅外線傳感器檢測進出旋轉門的人員流動，使用多個接觸式和非接觸式傳感器及光電接近開關來確保通行安全。 關鍵詞：自動旋轉門；控制系統；安全系統；PLC；變頻器 Abstract Three wings automatic revolving door is leading products in automatic doors, it can give generously warm and feeling and creating luxurious atmosphere, Meanwhile, it is a eye in modern building . The biggest characteristic is that it "open and closed forever, forever", namely, the door for people to always can open doors, building and always closed. Therefore, the automatic revolving door in function of unique development. The graduation design mainly discusses the design about control system and safely system of the three wings automatic revolving door. PLC is responsible for the task of controller and the function of rotational speed is rely on the VVF. According to the requirements of PLC for the selected models FXOS-32MR-001and related data PLC hookup。According to the function requirement JiaLing chose JP6C - T9-0.75 and type inverter control system of the electrical diagram。People passing in and off the revolving door is checked by the infrared ray sensor, the safety of people are ensured by many contact and non-contact sensors and photoelectric proximity switches KeyWords：automatic revolving door，control system，safely system，PLC，Inverter 目　　錄 摘　　要 I Abstract I 1.緒論……………………………………………………………………………...…..1 1.1選題背景…………………………………………………………………1 1.1.1旋轉門淺析…………………………………………………….……....2 1.2自動旋轉門設計實例……………………………………………………3 2系統整體方案設計………………………………………………………………….5 2.1 PLC控制系統功能要求分析………………… ………………….….5 2.2 PLC控制系統設計方案 6 2.2.1 PLC控制系統設計的基本原則 ..6 2.2.2 PLC控制系統設計方案……………………………………………….6 3.PLC硬件系統設計…………………………………...……………………………..8 3.1PLC簡介………………………………………………………………….8 3.1.1PLC基本結構…………………………………………………………..8 3.1.2 PLC的工作原理…………………………………………………. ….12 3.1.3 PLC的應用領域及發展趨勢……………………………………..….14 3.2 PLC控制系統硬件設計……………………………………………..…16 3.2.1 PLC選型及I/O分配確定………………………………………..….16 3.2.2變頻器選型……………………………………………….…..………19 3.2.3傳感器選型及安全系統設計…………………………………..….…27 3.2.4其它設備選型………………………………………………..…….…33 3.2.5 PLC I/O接線圖設計………………………………………..………..33 3.2.6電控系統電氣原理圖設計…………………………………..….……33 結論…………………………………………………………………………………..37 致謝…………………………………………………………………………………..38 參考文獻…………………………………………………..…………………………39